Öle

Innovation and quality 'made in Germany'

Minimum quantity lubrication for any job

You can name any application scenario in a large-scale industry or in a small enterprise: UNICUT® products are tailor-made to meet your requirements plus they have been fine-tuned to various ferrous materials and different kinds of applications.

Amongst them is the internationally patented UNICUT® Duplex-System which combines the benefits of minimum quantity lubrication with the strong points of oil and emulsion lubrication.

What all our products have in common: our development is based on our experience of 45 years which always meets top quality standards.

New names – proven quality

Since 1 September 2011 we have optimised our product names. Please make sure you use the correct term when ordering. Quality and composition of the products remain unchanged. We have just shortened and simplified the names to improve our service for you. Thus application fields can be identified and assigned much easier and the likelihood of confusing any products is reduced. > Product Key

UNICUT® Basic-EP

UNICUT® Basic-EP

RANGE OF SERVICES: Wide range, all-round
MATERIALS: Aluminium, non-ferrous metals, C steels and CrNi steels
CHARACTERISTICS: Based on mineral oil, medium viscous, all-purpose use
MACHINING METHODS: Drilling, rubbing, bandsawing, milling, turning, circular sawing, reaming

TECHNICAL CHARACTERISTICS

  • Viscosity 30 cSt at 40 °C
  • Based on mineral oil
  • Excellent lubrication effect
  • Usable with all commercially approved MQCL spraying stations
  • Free of evaporation-promoting solvents
  • Free of silicone as well as chlorine and other halogens

ADVANTAGES

  • Cost saving due to increasing the machining speed
  • Reduction tool costs
  • Avoiding built-up edges
  • Less downtime due to by tool change
  • No costs for cooling agent disposal
  • Ideal for companies with high material variety
  • Cost-effective due to low consumption
  • Good skin tolerance and environmentally friendly

AVAILABLE CONTAINER SIZES

  • 10-, 20-, 30-litre HDPE containers
  • 200-litre disposable barrel
  • 1,000-litre container

For personal advice we are at your disposal. Your UNICUT® Team.

Please download by clicking the product sheet:

UNICUT® Basic-HT

UNICUT® Basic-HT

RANGE OF SERVICES: Wide range, all-round
MATERIALS: Aluminium, non-ferrous metals, C steels and CrNi steels
CHARACTERISTICS: Based on mineral oil, highly viscous, high temperature resistant, all-purpose use
MACHINING METHODS: Circular sawing, ingot milling


TECHNICAL CHARACTERISTICS

  • Viscosity 212 cSt at 40 °C
  • Based on mineral oil
  • High temperature resistant
  • For high-performance processing machines
  • Excellent lubrication effect
  • Especially adhesive
  • Also suitable and well-tried for aviation and space flight alloys
  • Suitable for silicon-containing alloys and pure aluminium
  • Suitable for special non-ferrous metal alloys
  • Usable with all commercially approved pumping and spraying MQCL stations
  • Recyclable and dry shavings
  • Free of silicon as well as chlorine and other halogens

ADVANTAGES

  • Cost saving due to increasing the machining speed
  • Reduction of tool costs
  • Avoiding built-up edges
  • Less downtime due to by tool change
  • No costs for cooling agent disposal
  • Ideal for companies with high material fluctuation
  • Cost-effective due to low consumption
  • Good skin tolerance and environmentally friendly
  • No staining during heating-up on hot rolling temperature
  • Grooveless milled surfaces

AVAILABLE CONTAINER SIZES

  • 10-, 20-, 30-litre HDPE containers
  • 200-litre disposable barrel
  • 1,000-litre container

For personal advice we are at your disposal. Your UNICUT® Team.

Please download by clicking the product sheet:

UNICUT® Basic-V

UNICUT® Basic-V

RANGE OF SERVICES: Wide range, all-round
MATERIALS: Aluminium, non-ferrous metals, C steels and CrNi steels
CHARACTERISTICS: Based on mineral oil, medium viscous, high temperature resistant, all-purpose use
MACHINING METHODS: Circular sawing, bandsawing, milling, ingot milling, rubbing, reaming, turning


TECHNICAL CHARACTERISTICS

  • Viscosity 100 cSt at 40 °C
  • Based on mineral oil
  • For high-performance processing machines
  • For milling processes with subsequent plating
  • Excellent lubrication effect
  • Also suitable and well-tried for aviation and space flight alloys
  • Suitable for silicon-containing alloys and pure aluminium
  • Suitable for special non-ferrous metal alloys
  • Usable with all commercially approved pumping and spraying MQL stations
  • Recyclable and dry shavings
  • Free of silicon as well as chlorine and other halogens

ADVANTAGES

  • Cost saving due to increasing the machining speed
  • Reduction of tool costs
  • Avoiding built-up edges
  • Less downtime due to tool change
  • No costs for cooling agent disposal Ideal for companies with high variety of materials
  • Cost-effective due to low consumption
  • Good skin tolerance and environmentally friendly
  • Dry and grooveless milled surfaces

AVAILABLE CONTAINER SIZES

  • 10-, 20-, 30-litre HDPE containers
  • 200-litre disposable barrel
  • 1,000-litre container

For personal advice we are at your disposal. Your UNICUT® Team.

Please download by clicking the product sheet:



UNICUT® Alu-MF

UNICUT® Alu-MF

RANGE OF SERVICES: High-tech special product
MATERIALS: Aluminium and its alloys, non-ferrous metals
CHARACTERISTICS: Free of mineral oil, biodegradable, low viscous
MACHINING METHODS: Drilling, bandsawing, circular sawing, milling, turning


TECHNICAL CHARACTERISTICS

  • Viscosity 25 cSt at 40 °C
  • Free of mineral oil
  • Biodegradable
  • Developed in cooperation with leading producers of bandsaws
  • Excellent lubrication effect
  • Also suitable and well-tried for aviation and space flight alloys
  • Suitable for high-silicon-content alloys and pure aluminium
  • Usable with all commercially approved MQCL spraying stations
  • Recyclable and dry swarf
  • Free of silicone as well as chlorine and other halogens

ADVANTAGES

  • Very high tool service lives: bandsaws up to 3,000 m2 /band
  • Cost saving due to enormous increase of the machining speed
  • Reduction of tool costs
  • Avoiding built-up edges
  • Less downtime due to tool change
  • No costs for cooling agent disposal
  • Cost-effective due to low consumption
  • Good skin tolerance and environmentally friendly
  • Dry and grooveless milled surfaces

AVAILABLE CONTAINER SIZES

  • 10-, 20-, 30-litre HDPE containers
  • 200-litre disposable barrel
  • 1,000-litre container

For personal advice we are at your disposal. Your UNICUT® Team.

Please download by clicking the product sheet:


UNICUT® Alu-SI

UNICUT® Alu-SI

RANGE OF SERVICES: High-tech special product
MATERIALS: AlSi alloys, aluminium, non-ferrous metals
CHARACTERISTICS: Free of mineral oil, biodegradable, low viscous
MACHINING METHODS: Drilling, bandsawing, circular sawing, milling, turning


TECHNICAL CHARACTERISTICS

  • Viscosity 25 cSt at 40 °C
  • Free of mineral oil
  • Biodegradable
  • Developed in cooperation with leading producers of bandsaws
  • Excellent lubrication effect
  • Developed especially forhigh-silicon-content alloys
  • Also suitable and well-tried for aviation and space flight alloys
  • Usable with all commercially approved MQCL spraying stations
  • Recyclable and dry swarf
  • Free of silicone as well as chlorine and other halogens

ADVANTAGES

  • Very high tool service lives
  • Cost saving due to enormous increase of the machining speed
  • Reduction tool costs
  • Avoiding built-up edges
  • Less downtime due to by tool change
  • No costs for cooling agent disposal
  • Cost-effective due to low consumption
  • Good skin tolerance and environmentally friendly

AVAILABLE CONTAINER SIZES

  • 10-, 20-, 30-litre HDPE containers
  • 200-litre disposable barrel
  • 1,000-litre container

For personal advice we are at your disposal. Your UNICUT® Team.

Please download by clicking the product sheet:

UNICUT® Alu-Milling

UNICUT® Alu-Milling

RANGE OF SERVICES: High-tech special product
MATERIALS: Aluminium and its alloys, non-ferrous metals
CHARACTERISTICS: Free of mineral oil, biodegradable, low viscous
MACHINING METHODS: Ingot milling


TECHNICAL CHARACTERISTICS

  • Viscosity 25 cSt at 40 °C
  • Free of mineral oil
  • Biodegradable
  • Especially suitable for aluminium milling
  • Developed in cooperation with leading makers of ingot milling machines
  • Excellent lubrication effect
  • Also suitable and well-tried for aviation and space flight alloys
  • Surfaces suitable for plating after milling
  • Also suitable for high-silicon-content alloys as well as pure aluminium
  • Preferably usable with the UNICUT® special spraying equipment UDDS
  • Recyclable and dry swarf
  • Free of silicone as well as chlorine and other halogens

ADVANTAGES

  • Very high tool service lives
  • Cost saving due to enormous increase of the machining speed
  • Clean glassy surfaces
  • No built-up edges
  • Machine parts are suitable for plating without time-consuming finishing treatment
  • Enormous reduction of tool costs
  • Less downtime due to by tool change
  • No costs for cooling agent disposal
  • Cost-effective due to low consumption
  • Good skin tolerance and environmentally friendly
  • Dry and grooveless milled surfaces

AVAILABLE CONTAINER SIZES

  • 10-, 20-, 30-litre HDPE containers
  • 200-litre disposable barrel
  • 1,000-litre container

For personal advice we are at your disposal. Your UNICUT® Team.

Please download by clicking the product sheet:

UNICUT® Alu-Separator

UNICUT® Alu-Separator

RANGE OF SERVICES: High-performance separating agent
MATERIALS: Production of aluminium granules
CHARACTERISTICS: Based on mineral oil, highly viscous
MACHINING METHODS: Casting of granules


TECHNICAL CHARACTERISTICS

  • Viscosity 364 cSt at 40 °C
  • Premium separating agent for the production of aluminium granules
  • Based on mineral oil
  • Suitable for use at high temperatures
  • Usable on all granules units
  • No hazardous materials
  • Free of silicone as well as chlorine and other halogens

ADVANTAGES

  • No more adherence
  • Good adhesive power
  • Low consumption, highest productiveness
  • Convincing cost/performance ratio
  • No smoke development

AVAILABLE CONTAINER SIZES

  • 10-, 20-, 30-litre HDPE containers
  • 200-litre disposable barrel
  • 1,000-litre container

For personal advice we are at your disposal. Your UNICUT® Team.

Please download by clicking the product sheet:


UNICUT® Steel-A4

UNICUT® Steel-A4

RANGE OF SERVICES: High-tech special product
MATERIALS: C steels, CrNi steels, high-alloy steels, titanium and special materials
CHARACTERISTICS: Free of mineral oil, biodegradable, medium viscous
MACHINING METHODS: Drilling, rubbing, bandsawing, milling, turning, circular sawing, reaming


TECHNICAL CHARACTERISTICS

  • Viscosity 60 cSt at 40 °C
  • Free of mineral oil
  • Biodegradable
  • For high-performance metal-cutting machines
  • Extremely suitable for difficult-to-machine materials like austenitic steels, special materials like Nimonic
    and Hastelloy as well as highly heat-resistant steels
  • Excellent lubrication effect
  • Usable with all commercially approved MQCL equipment
  • Recyclable and dry swarf
  • Free of silicon as well as chlorine and other halogens

ADVANTAGES

  • Very high tool service lives
  • Cost saving due to enormous increase of the machining speed
  • Clean and smooth surfaces
  • Reduction of tool costs
  • Less downtime due to by tool change
  • No costs for cooling agent disposal
  • Cost-effective due to low consumption
  • Good skin tolerance and environmentally friendly

AVAILABLE CONTAINER SIZES

  • 10-, 20-, 30-litre HDPE containers
  • 200-litre disposable barrel
  • 1,000-litre container

For personal advice we are  at your disposal. Your UNICUT® Team.

Please download by clicking the product sheet:


UNICUT® Duplex-System

UNICUT® Duplex-System

RANGE OF SERVICES: High-end special solution
MATERIALS: C steels, CrNi steel, high-alloy steels and high-grade steels, titanium and most difficult-to-machine special materials
CHARACTERISTICS: Minimal quantity coolant lubrication (MQCL),free of mineral oil, biodegradable
MACHINING METHODS: Bandsawing, circular sawing, milling, turning, drilling


TECHNICAL CHARACTERISTICS

  • Machining with very efficient synergetic effect: the arising rubbing is reduced to a
    minimum by means of a special high-performance lubrication fluid. The remaining
    afterheat is then eliminated by a micromist out of the high-performance fluid especially
    fine-tuned to the cooling fluid
  • Minimal quantity coolant lubrication (MQCL)
  • For the maching of steel, C steels, high-grade steel as well as special materials like
    titanium, CrNiMo steels, vanadium steels, nickel, Ni-base alloys, Hastelloy and Inconel
  • Free of mineral oil
  • Biodegradable
  • Excellent lubrication and cooling efficiency
  • With HM tools self-induction hot cut is possible
  • Recyclable and dry shavings
  • Free of silicone as well as chlorine and other halogens

ADVANTAGES

  • Clean and smooth surfaces
  • Considerable tool cost savings
  • Noticeable increase of production efficiency
  • Considerably reduced fixed cycles at equal tool life
  • No adhesive or resinous residues
  • No costs for cooling agent disposal
  • Good skin tolerance and environmentally friendly

AVAILABLE CONTAINER SIZES

  • 10-, 20-, 30-litre HDPE containers
  • 200-litre disposable barrel
  • 1,000-litre container

For personal advice we are at your disposal. Your UNICUT® Team.

Please download by clicking the product sheet:


UNICUT® VA

UNICUT® VA

RANGE OF SERVICES: All-purpose product for manual working
MATERIALS: Aluminium, non-ferrous metals and lowly alloyed C-steels and CrNi-steels
CHARACTERISTICS: Based on mineral oil, medium viscous
MACHINING METHODS: Manual working, drilling, threading, rubbing, reaming etc.


TECHNICAL CHARACTERISTICS

  • Viscosity 30 cSt at 40 °C
  • Based on mineral oil
  • Broad spectrum cutting oil for simple processes of machining like drilling, threading, rubbing, reaming etc. of almost all commercially approved materials
  • Usable with all commercially approved hand-dosing bottles or similar
  • Free of silicone as well as chlorine and other halogens

ADVANTAGES

  • Clean and smooth surfaces
  • Considerable tool cost savings
  • Less standstills by tool change
  • Cost effective by highest performance and least consumption
  • Recycable and dry shavings
  • No costs for cooling agent disposal
  • No unpleasant cooling agent disposal
  • Good skin tolerance and environmentally friendly

AVAILABLE CONTAINER SIZES

  • 10-, 20-, 30-litres HDPE-container
  • 200-litre disposable barrel
  • 1,000-litre container

For personal advice we are glad to be at your disposal. Your UNICUT® Team.

Please download by clicking the product sheet:


UNICUT® TX

UNICUT® TX

RANGE OF SERVICES: Special product for manual working
MATERIALS: C steels, CrNi steels as well as Nimonic, Hastelloy
CHARACTERISTICS: Based on mineral oil, medium viscous
MACHINING METHODS: Manual working, drilling, threading, rubbing, reaming, etc.


TECHNICAL CHARACTERISTICS

  • Viscosity 30 cSt at 40 °C
  • Based on mineral oil
  • Special cutting oil for difficult machining processes
  • Usable with all commercially approved hand-dosing bottle
  • Suitable as high-pressure additive for automatic machine oils
  • Free of silicone as well as chlorine and other halogens

ADVANTAGES

  • Clean and smooth surfaces
  • Tool cost savings
  • Less downtime due to by tool change
  • Cost-effective due to highest performance and least consumption
  • Recyclable and dry swarf
  • No costs for cooling agent disposal
  • No unpleasant cooling agent disposal
  • No adhesive or resinous residues
  • Good skin tolerance and environmentally friendly

AVAILABLE CONTAINER SIZES

  • 10-, 20-, 30-litres HDPE containers
  • 200-litre disposable barrel
  • 1,000-litre container

For personal advice we are at your disposal. Your UNICUT® Team.

Please download by clicking the product sheet:


UNICUT® Autocut

UNICUT® Autocut

RANGE OF SERVICES: High-performance automatic and punching oil
MATERIALS: Aluminium, non-ferrous metals, C steels and CrNi steels
CHARACTERISTICS: Based on mineral oil, medium viscous
MACHINING METHODS: Automatic turning, cutting-off, punching and bending


TECHNICAL CHARACTERISTICS

  • Viscosity 30 cSt at 40 °C
  • Based on mineral oil
  • High-performance automatic and punching oil for the machining of almost all
    commercially approved materials, also suitable for non-ferrous metals
  • Usable with all commercially approved flooding equipment
  • Free of silicon as well as chlorine and other halogens

ADVANTAGES

  • Clean and smooth surfaces
  • No built-up edges
  • Tool cost savings
  • Reduces cycle times and thus operating costs
  • No resinous residues
  • No costs for cooling agent disposal
  • No unpleasant cooling agent disposal
  • Good skin tolerance and environmentally friendly

AVAILABLE CONTAINER SIZES

  • 10-, 20-, 30-litre HDPE containers
  • 200-litre disposable barrel
  • 1,000-litre container

For personal advice we are at your disposal. Your UNICUT® Team.

Please download by clicking the product sheet:

Your contact to UNICUT® Phone: +49 (0)2622 4266
Fax: +49 (0)2622 2603
Email: info@unicut.de Request Information